Contents of the Kit
|| Reaction Buffer
||:100 µl x1
||:100 µl x 1
Storage Condition: 0-5ºC
Shipping Condition: ambient temperature
Required Equipment and Materials
20 µl, 200 µl adjustable pipettes, Microtube (for sample and Working Buffer preparation, 37ºC incubator, PBS(Phosphate buffered saline), DMSO (Dimethyl sulfoxide)
Ab-10 Rapid Biotin Labeling Kit enables rapid (in less than 30 min) and easy labeling of Biotin to 10 μg antibody. Reactive Biotin (a component of the kit) has succinimidyl ester group, that can easily make a covalent bond with an amino group of the target antibody without any activation process. This kit contains all the necessary reagents to prepare a Biotin-labeled antibody except for DMSO.
Fig. 1 Labeling Procedure
♦ Use 0.5-1 mg/ml of antibody solution for labeling. If the antibody concentration is more than 1 mg/ml, please dilute the antibody solution with PBS.
♦ If the sample solution contains small insoluble materials, centrifuge the solution, and use the supernatant for the labeling.
♦ The microtubes in this kit contain solutions. Since there is a possibility that the droplets might attach to the inside walls or caps, please spin the tube to drop them down prior to open.
♦ In case an antibody solution includes a high concentration of constituents, such as BSA or glycerol, it may interfere with a labeling and cause a non-specific signal. We recommend removing the constituents prior to labeling procedure. Usable constituents (○) and non-usable constituents (×) are shown in Table 1, and compatible concentrations of constituents are shown in Table 2.
♦ Interference and non-specific signal may be dependent on types of antigen, host species of antibody or constituents.
♦ Since reactive reagent binds to an amino group in antibody, there is a possibility that the labeled antibody loses the antigen recognition ability (Table 3).
Table. 1 Usable / Non-usable Constituents
Table. 2 Compatible Concentration of Constituents
Table. 3 Non-Compatible Antibody
1. HeLa cells were seeded on a μ-slide 8 well (ibidi) and cultured overnight at 37 ºC in a 5% CO2 incubator.
2. The cells were washed with PBS three times, and 4% paraformaldehyde in PBS was added to the μ-slide.
3. The μ-slide was incubated at room temperature for 15 minutes.
4. The cells were washed with PBS three times, and 1% Triton-X in PBS was added to the μ-slide.
5. The μ-slide was incubated at room temperature for 30 minutes.
6. Once the cells were washed with PBS three times, a blocking solution prepared with PBS was added to the μ-slide.
7. The cells were then incubated at room temperature for 1 hour.
8. Biotin conjugated anti-mitochondria antibody was diluted 50 times with the blocking solution. ※Anti-mitochondria antibody was purchased from Abcam (Product Code: ab3298) .
9. The supernatant was discarded and the solution (step 8) was added to the μ-slide.
10. The μ-slide was incubated at 0-5ºC overnight.
11. The supernatant was discarded and the cells were washed using PBS-T three times.
12. 0.2 µg/ml peroxidase conjugated streptavidin was added to the μ-slide.
13. The μ-slide was incubated at room temperature for 1 hour.
14. The supernatant was discarded and the cells were washed using PBS-T three times.
15. The cells were washed using Tris buffer (TB, 50 mmol/l, pH 7.5) three times.
16. The supernatant was discarded and DAB solution [0.2 mg/ml DAB (SKU:D006), 0.003% H2O2 , 50 mmol/l Tris (pH 7.5)] was added to the μ-slide.
17. The μ-slide was incubated at room temperature for 10 minutes.
18. After the cells were washed using TB three times, TB was added to the μ-slide.
19.The cells were observed under a microscope.
Fig. 2 Microscope image of DAB-stained mitochondria in HeLa cells